CRACK SEALING, WATER STOPPING & WATERPROOFING
EPOXY
DESIGNATION
DESCRIPTION
PRINCIPLE USES
COVERAGE / YIELD
TDS
CONDUR SC
Pure synthetic resin with low viscosity for sealing cracks, cavities with a maximum width of approx. 5 mm.
For concrete crack repair to bridges, beams, columns, precast elements, floors etc.
See data sheet.
POLYURETHANE
DESIGNATION
DESCRIPTION
PRINCIPLE USES
COVERAGE / YIELD
TDS
CONTITE PU100/101
A one component hydrophobic polyurethane injection grout, an effective means of stopping water seepage. The system only reacts when it comes into contact with water producing a relatively stiff polyurethane foam.
Used to stop water penetration or react away water in cracks, voids or soil. Areas of use include basements, tunnels all underground structures, reservoirs, pools etc.
See data sheet.
CONTITE PUE200/201
A two component environmentally friendly polyurethane system. For flexible sealing of cracks in concrete structures as well as areas suffering from water leakage.
Can be used directly into dry & moist cracks, if water leakage must be stopped first use Contite PU100/101.
See data sheet.
CONTITE PUE300/301
A two component environmentally friendly polyurethane system. This
system is ideal for the structural sealing of cracks in concrete structures as well as areas suffering
from water leakage.
Can be used directly into dry & moist cracks, if water leakage must be stopped first use Contite PU100/101.
See data sheet.
CONTITE PUE400/E401
A two component hydrophobic polyurethane 2 in 1 injection resin system.
Used to stop water leakage as well as to form a solid resin, one shot permanent sealing of cracks.
See data sheet.
CONTITE PUE500/501
A phthalate free fast reacting 2 component rigid polyurethane foam.
Use to increase the load bearing capacity of loose soils. For soil & rock consolidation, filling of large voids, cracks and crevices in wet & dry consolidations. Pre-injection waterproofing in front of TBMs.
See data sheet.
CONTITE G600
A hydrogel injection grout. Used to stop heavy water leakage. Reacts with water over a range of ratios to form elastic foams, rubbery gasket or elastomeric waterproof gel.
Typical areas of use include shutting off water seepage, forming a positive side waterproof membrane with below grade structures injected from the negative side, for reinjectable hoses & soil stabilization, prevention of water leakage in sewerage and drain pipes, ground stabilization, prevention of water leaks through expansion or construction joints.
See data sheet.
FLEXIBLE SEALING
DESIGNATION
DESCRIPTION
PRINCIPLE USES
COVERAGE / YIELD
TDS
CONTITE PUE200/201
A two component environmentally friendly polyurethane system. For flexible sealing of cracks in concrete structures as well as areas suffering from water leakage.
Can be used directly into dry & moist cracks, if water leakage must be stopped first use Contite PU100/101.
See data sheet.
CONTITE PUE400/E401
A two component hydrophobic polyurethane 2 in 1 injection resin system.
Used to stop water leakage as well as to form a solid resin, one shot permanent sealing of cracks.
See data sheet.
STRUCTURAL SEALING EPOXY & POLYURETHANE
RIGID
DESIGNATION
DESCRIPTION
PRINCIPLE USES
COVERAGE / YIELD
TDS
CONDUR SC
Pure synthetic resin with low viscosity for sealing cracks, cavities with a maximum width of approx. 5 mm.
For concrete crack repair to bridges, beams, columns, precast elements, floors etc.
See data sheet.
CONTITE PUE300/301
A two component environmentally friendly polyurethane system. This
system is ideal for the structural sealing of cracks in concrete structures as well as areas suffering
from water leakage.
Can be used directly into dry & moist cracks, if water leakage must be stopped first use Contite PU100/101.
See data sheet.
WATERPROOFING GEL AND SEAL
DESIGNATION
DESCRIPTION
PRINCIPLE USES
COVERAGE / YIELD
TDS
CONTITE G600
A hydrogel injection grout. Used to stop heavy water leakage. Reacts with water over a range of ratios to form elastic foams, rubbery gasket or elastomeric waterproof gel.
Typical areas of use include shutting off water seepage, forming a positive side waterproof membrane with below grade structures injected from the negative side, for reinjectable hoses & soil stabilization, prevention of water leakage in sewerage and drain pipes, ground stabilization, prevention of water leaks through expansion or construction joints.
See data sheet.
Concrete Injection
EPOXY
POLYURETHANE
DESIGNATION : CONTITE PUE300/301
DESCRIPTION : A two component environmentally friendly polyurethane system. This
system is ideal for the structural sealing of cracks in concrete structures as well as areas suffering
from water leakage.
PRINCIPLE USES : Can be used directly into dry & moist cracks, if water leakage must be stopped first use Contite PU100/101.
COVERAGE / YIELD : See data sheet.
DESIGNATION : CONTITE PUE500/501
DESCRIPTION : A phthalate free fast reacting 2 component rigid polyurethane foam.
PRINCIPLE USES : Use to increase the load bearing capacity of loose soils. For soil & rock consolidation, filling of large voids, cracks and crevices in wet & dry consolidations. Preinjection waterproofing in front of TBMs.
COVERAGE / YIELD : See data sheet.
DESIGNATION : CONTITE PUE700/701
DESCRIPTION : Two part fast setting rigid polyurethane foam for soil & rock consolidation and below grade water stoppage
PRINCIPLE USES : Used for soil and rock consolidation, filling of large voids, cracks and crevices, pre injection for waterproofing and consolidation in front of TBMs and drill and blast, filling of fissures, gravel layers, in wet and dry conditions.
COVERAGE / YIELD : See data sheet.
FLEXIBLE SEALING
DESIGNATION : CONTITE PUE200/201
DESCRIPTION : A two component environmentally friendly polyurethane system. For flexible sealing of cracks in concrete structures as well as areas suffering from water leakage.
PRINCIPLE USES : Can be used directly into dry & moist cracks, if water leakage must be stopped first using Contite PU100/101.
COVERAGE / YIELD : See data sheet.
DESIGNATION : CONTITE PUE400/E401
DESCRIPTION : A two component hydrophobic polyurethane 2 in 1 injection resin system.
PRINCIPLE USES : Used to stop water leakage as well as to form a solid resin, one shot permanent sealing of cracks.
COVERAGE / YIELD : See data sheet.
RIGID
DESIGNATION : CONTITE PUE500/501
DESCRIPTION : A phthalate free fast reacting 2 component rigid polyurethane foam.
PRINCIPLE USES : Use to increase the load bearing capacity of loose soils. For soil & rock consolidation, filling of large voids, cracks and crevices in wet & dry consolidations. Preinjection waterproofing in front of TBMs.
COVERAGE / YIELD :See data sheet.
FLEXIBLE
DESIGNATION : CONTITE PU100/101
DESCRIPTION : A one component hydrophobic polyurethane injection grout, an effective means of stopping water seepage. The system only reacts when it comes into contact with water producing a relatively stiff polyurethane foam.
PRINCIPLE USES : Used to stop water penetration or react away water in cracks, voids or soil. Areas of use include basements, tunnels all underground structures.
COVERAGE / YIELD : See data sheet.
GELS
DESIGNATION : CONTITE G600
DESCRIPTION :A hydrogel injection grout. Used to stop heavy water leakage. Reacts with water over a range of ratios to form elastic foams, rubbery gasket or elastomeric waterproof gel.
PRINCIPLE USES :Typical areas of use include shutting off water seepage, forming a positive side waterproof membrane with below grade structures injected from the negative side, for reinjectable hoses & soil stabilization, prevention of water leakage in sewerage and drain pipes, ground stabilization, prevention of water leaks through expansion or construction joints.
COVERAGE / YIELD : See data sheet.
